Cal Aqua Labs Inline Diffusor
- Made of high-quality glass
- Efficient CO2 atomisation through ceramic membrane
- Visually very appealing
- The necessary suction cups are included
- Fits 16/22 mm hose
Sign in or Register
Item question
We’re here for you!
Please enter your question and e-mail and we’ll contact you as soon as possible. It usually takes us up to 24 hours during business days to respond.
Thank you for your question!
Thank you, we’ll get in touch!
Close window
You already sent us a question.
Please wait a few minutes
Description
CO2 diffusers no longer need to be inside your aquarium! For the first time, Cal Aqua Labs offers a CO2 diffuser that attaches inline to your canister outflow, concealing it from view of your aquarium.
The new 13 mm mini inline diffuser has a 25 mm diameter diffuser disc at the center encased within a glass chamber. Unlike many other inline reactors, the inline diffuser disperses CO2 with minimal reduction in flowrate. The input and output ports connect to 1/2" (12/16 mm) diameter tubing. Recommended for nano tanks and aquariums up to 30 gallons (approx. 200 liters). The unit also has two built-in attachment points for detachable suction cups and can be securely attached to the side of the tank. Supplied with two suction cups.
Features
- One less equipment inside your aquarium
- Enhanced CO2 dissolution via turbulent mixing
- Minimal reduction in flow compared to many CO2 reactors
- Small and compact size
- Creates a fine mist of CO2 shown by many to further enhance plant growth
- Reduce photosynthetic algae growth on diffuser disc when placed away from direct light (ie. outside of tank or inside tank cabinet)
- Active flow around diffuser prevents debris buildup on diffuser disc
Usage
- Install the diffuser in the outflow line of the canister filter according to the diagram below. The diffuser can be attached up high next to the aquarium, or down below inside the cabinet. Use a high-quality check-valve
- CO2 from a pressurized source is recommended
- Always wet glass surfaces before fitting tubing. Tubing can be soften by dipping in hot water
- To prevent damage to glassware, do not use excessive force when fitting or removing tubing. We strongly recommend using soft silicone tubing for all glassware
- Do not shake or tap the diffuser against hard surfaces
We recommend to use soft silicone tubing to connect the glassware in order to reduce the risk of glass breakage. The piece of hose used should be kept as short as possible in order to avoid unnecessary CO2 losses.
Silicone hose is not pressure resistant and therefore can not be used for connection to the pressure regulator.
Dimensions
| Cal Aqua Labs - Inline Diffusor - 13 mm Mini | |
|---|---|
| Height | 110 mm |
| Diameter of diffuser disk | 20 mm |
| Fits hose | 13 mm or 12/16 mm |
| Cal Aqua Labs - Inline Diffusor - 13 mm | |
|---|---|
| Height | 130 mm |
| Diameter of diffuser disk | 25 mm |
| Fits hose | 13 mm or 12/16 mm |
| Cal Aqua Labs - Inline Diffusor - 17 mm | |
|---|---|
| Height | 130 mm |
| Diameter of diffuser disk | 25 mm |
| Fits hose | 17 mm or 16/22 mm |
Cleaning
When algae start forming on your glassware equipment or when larger and larger bubbles emerge from your ceramic diffusor it is time for cleaning. Glassware is easy to clean, however, it should be done diligently. After the cleaning process, your glassware products will be as good as new.
- You'll need a household bleach containing chlorine without perfumes. When working with chlorine bleach, please make sure you absolutely observe the manufacturer's safety notes.
- Pour some of the bleach into a container and mix with an equal amount of water. Mix so much of this solution that the glassware products you wish to clean are entirely covered
- Soak the glassware in the solution for 1 to 4 hours (depending on the severity of the stains)
- Take it out and rinse thoroughly
- Now all the stains ought to be gone, and your glassware should shine as if new
You'll find an extensive how-to (in German) with pictures in our Aquascaping Wiki under Glaswaren reinigen.
Cal Aqua Labs
A stunning quality and innovative ideas around glassware articles for aquascapes have a name: Cal Aqua Labs. Lily pipes, permanent CO2 tests or inline diffusers are manufactured by highly experienced glass blowers. Their basic material is glass of the highest quality, whose clarity and stability is just stunning. The glassware is carefully manufactured by hand in keeping with very high quality standards. Every aquascape is embellished by these beautiful yet unobtrusive glassware products.
Those who do not want to compromise when it comes to glassware for aquascaping are exactly right to look at products by Cal Aqua Labs.
General information
| Item no. |
|
| EAN | 4250585202580 |
| Weight | 0,50 kg |
| Shipping weight | 0,50 kg |
Customers ask customers
You have questions about this product? Ask other customer or our support team about this product!
Customer reviews
2 Reviews
| 5 Stars(1) |
|
| 4 Stars(1) |
|
| 3 Stars(0) |
|
| 2 Stars(0) |
|
| 1 Star(0) |
|
Superb design, but I hoped that it wouldn't clogg as traditional diffusers you have in the tank! They clogg, but not as fast as the normal diffusers! (read more)